Proceedings (in English)

　　

2023

  • Suzuki, Y., and Miyoshi, T.,
    Plenary talk, “Wearable/skin-attached Energy Harvesters with High-performance Amorphous Polymer Electrets,”
    1st Int. Conf. on Scientific Exhibition Living Materials Systems, Freiburg, (2023).
  • Suzuki, Y.,
    Keynote talk, “Quantitative Measurement of Wall Chemical Effects for Hydrocarbon/ammonia Flames,”
    14th Asia-Pacific Conference on Combustion (ASPACC), Kaohsiung, (2023).
  • Lee, M., Li, G., and Suzuki, Y.,
    “Investigation of Pressure Effects on Cool Flame Ignition Temperature through the Gas Temperature-compensated HCHO-TDLAS Measurement,”
    14th Asia-Pacific Conference on Combustion (ASPACC), Kaohsiung, 142, (2023).
  • Miyoshi, T., and Suzuki, Y.,
    “Design and Modeling of Wrist-Worn Rotational Electret Energy Harvester for Battery-less Wearable Devices,”
    The 18th Int. Conf. Nano/Micro Engineered and Molecular Systems (IEEE NEMS 2023), Jeju, (2023).
  • Wang, R., Suzuki, K., Takebe, M., Zhang, Y., Miyoshi, T., and Suzuki, Y.,
    “Stretchable Fluorinated Electret for Skin-attachable Energy Harvester,”
    22nd Int. Conf. Solid-state Sensors, Actuators, and Microsystems (Transducers ’23), Kyoto, (2023),pp. 1284-1287.
  • Miyoshi, T., and Suzuki, Y.,
    “Boadband Power Generation from Arm Swing During Walking by Repulsive-torque-enhanced Rotational Electret Energy Harvester,”
    22nd Int. Conf. Solid-state Sensors, Actuators, and Microsystems (Transducers ’23), Kyoto, (2023),pp. 2034-2037.
  • Xu, X., Lee, M., and Suzuki, Y.,
    “Measurements of NH3 and NH2* Profiles in Ammonia Counterflow Diffusion Flames,”
    2nd Symp. on Ammonia Energy, Orleans, (2023).
  • Lee, M., Li, G., Mizuno, T., and Suzuki, Y., “Effects of Surface Reactivity and Pressure on Cool Flame Ignition Characteristics,” 17th Int. Heat Transfer Conf. (IHTC-17), Cape Town, (2023), 526.
  • Suzuki, Y., Lee, M., Yoo, G., "Convection-effect-enhanced Thermoelectric Power Generation Directly-heated by Catalytic Combustion," 17th Int. Heat Transfer Conf. (IHTC-17), Cape Town, (2023), 779.
  • Miyoshi, T., Wang, R., Suzuki, K., and Suzuki, Y., “Development of Skin-Attached Stretchable Energy Harvester with Perfluoroelastomer Electret,” IEEE 19th Int. Symp. Electrets (ISE19), Linz, (2023), p. 42.
  • Suzuki, Y., Invited talk, “Deep-learning-assisted Discovery of Amorphous Fluorinated Polymer Electret with Improved Charging Performance for Energy Harvesting,” IEEE 19th Int. Symp. Electrets (ISE19), Linz, (2023), p. 79.
  • Suzuki, Y., Plenary talk, “AI-assisted Optimization of End Group in Amorphous Fluorinated Polymer Electret for Vibration Energy Harvesting,” AMF-AMEC-2023, Macau, (2023).
  • Zhou, M., Suzuki, Y., and Lee, M., “TOF-MS Measurement of Intermediate Species in Wall-stabilized Premixed Cool Flames,” 20th Int. Conf. Fluid Dynamics, Sendai, (2023), OS2-35.
  • Miyoshi, T., Mei, X., and Suzuki, Y.,
    “On the Arm Swing Model during Human Walking for Wrist-worn Rotational Electret Energy Harvester,”
    22nd Int. Conf. on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2023), Abu Dhabi, TB3-02 (2023).
  • Fujita, T., Kannno, I., and Suzuki, Y.,
    “Evaluation Methods of Vibration Energy Harvester Reliability,”
    22nd Int. Conf. on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2023), Abu Dhabi, P2-11a (2023).

2022

  • Fan, Y., Wang, Z., Wang, Y., Lee, M., Kulatilaka, W. D., and Suzuki, Y.,
    “Effect of Thermal Dissociation in Rich Preheated Ammonia Micro Flames,”
    39th Int. Symp. Combustion (Combustion 2022), Vancouver, 4D03 (2022).
  • Wang, D., Lee, M., and Suzuki, Y.,
    “Nitriding Effects of Ammonia Flames on Iron-based Metal Walls,”
    39th Int. Symp. Combustion (Combustion 2022), Vancouver, WiPP-1P114 (2022).
  • Li, G., Lee, M., and Suzuki, Y.,
    “Ignition Characteristics of Premixed Cool Flame at Elevated Pressures Investigated by TDLAS,”
    39th Int. Symp. Combustion (Combustion 2022), Vancouver, WiPP-2P014 (2022).
  • Wang, D., Lee, M., and Suzuki, Y.,
    “Nitriding Effects of Ammonia Flames on Metal Walls Under Different Surface Temperatures,”
    1st Symp. on Ammonia Energy, Cardiff Univ., AP04 (2022).
  • Wang, R., Suzuki, K., Miyoshi, T., and Suzuki, Y.,
    “Intrinsically-stretchable Polymer Electret for Powering Skin Electronics,”
    21th Int. Conf. on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2022), Salt Lake City, T1A-01 (2022).
  • Miyoshi, T., Minegishi, G., and Suzuki, Y.,
    “Output Energy Evaluation of Wrist-worn Electret Energy Harvester for Day-long Activities of Daily Living,”
    21th Int. Conf. on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2022), Salt Lake City, T1A-02 (2022).
  • Miyoshi, T., Mori, T., and Suzuki, Y.,
    “Repulsive-torque-enhanced Wrist-worn Rotational Electret Energy Harvester,”
    21th Int. Conf. on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2022), Salt Lake City, W3A-03 (2022).
  • Takebe, M., Miyoshi, T., and Suzuki, Y.,
    “Stretchable Electret Energy Harvester Using the Fringe Field,”
    21th Int. Conf. on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2022), Salt Lake City, PT-10f (2022).

2021

  • Y. Fan, J. Guo, M. Lee, N. Iki, and Y. Suzuki,
    “Evaluation of Wall Chemical Effect in Hydrogen Flame,”
    38th Int. Symp. Combustion (Combustion 2020), Adelaide, 1B08, (2021).
  • M. Lee, T. Mizuno, and Y. Suzuki,
    “Wall Chemical Effects on Ignition Characteristics of Premixed DME/Oxygen Cool Flames,”
    38th Int. Symp. Combustion (Combustion 2020), Adelaide, WiPP-LF-11, (2021).
  • T. Mizuno, M. Lee, and Y. Suzuki,
    “Study on Ignition and Extinction Characteristics of n-Alkane Wall-stabilized Cool Flames,”
    38th Int. Symp. Combustion (Combustion 2020), Adelaide, WiPP-LF-14, (2021).
  • S. Sakamoto, M. Lee, and Y. Suzuki,
    “Investigation of Pressure Effects on Wall-stabilized Cool Flames Using TDLAS,”
    38th Int. Symp. Combustion (Combustion 2020), Adelaide, WiPP-LF-16, (2021).
  • Z. Wang, M. Lee, Y. Fan, and Y. Suzuki,
    “Investigation of Pyrolysis Effects on Ammonia Micro Flames,”
    38th Int. Symp. Combustion (Combustion 2020), Adelaide, WiPP-GPR-33, (2021).
  • Fan, Y., Wang, Z., Wang, Y., Lee, M., Kulatilaka, W.D., and Suzuki, Y.,
    “LIF Measurements of Species Structures in Ammonia Micro Flames,”
    12th US National Combustion Meeting, On-line, 2G10, (2021).
  • Lu, J., and Suzuki, Y.,
    "All-polymer Soft-X-ray-charged Piezoelectret for Push-button Energy Harvester,"
    21th Int. Conf. Solid-state Sensors, Actuators, and Microsystems (Transducers ’21), On-line, B2-225e, (2021).
  • Miyoshi, T., Mitsuya, H., Toshiyoshi, H., and Suzuki, Y.,
    "A Unified Design of Broadband Two-degree-of-freedom Vibration Energy Harvesting System for High-quality Factor Generators,"
    21th Int. Conf. Solid-state Sensors, Actuators, and Microsystems (Transducers ’21), On-line, B5-520e, (2021).
  • Suzuki, Y.,
    Plenary talk, “Machine-learning-based Design of Amorphous Polymer Electret for Vibration Energy Harvesting,”
    IEEE 18th Int. Symp. Electrets (ISE18), Shanghai, D2-1 (2021).
  • Zhang, Y., Mao, Z., Suzuki, K., and Suzuki, Y.,
    “Amorphous Polymer Electret Design Based on Solvation Model and Density Functional Theory with Deep Learning Approximation,”
    IEEE 18th Int. Symp. Electrets (ISE18), Shanghai, D2-7 (2021).
  • Lu, J., and Suzuki, Y.,
    “Push-Button Energy Harvester with Ultra-Soft All-Polymer Piezoelectret,”
    20th Int. Conference on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2021), online (2021).
  • Shimomura, N., Miyoshi, T., Ashizawa, H., Mitsuya, H., Hashiguchi, G., Suzuki, Y., and Toshiyoshi, H.,
    “Application of Two Degree-of-Freedom Vibrational Energy Harvesting Theory to Real Environmental Vibration,”
    20th Int. Conference on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2021), online (2021).
  • Mao, Z., Zhang, Y., Suzuki, K., Chen, C., Ong, S., and Suzuki, Y.,
    “Rapid Screening of Charge Stability in Amorphous Fluorinated Polymer Electret Based on Machine Learning,”
    IEEE Conf. Electr. Insul. Dielectr. Phenom. (CEIDP), Vancouver, (2021).
  • Feng, P., Lee, M., and Suzuki, Y.,
    “Effect of Wall Surface Materials on Ammonia Pyrolysis,”
    13th Asia-Pacific Conference on Combustion (ASPACC), Abu Dhabi, M1-06 (2021).
  • Mizuno, T., Lee, M., and Suzuki, Y.,
    “Ignition and Extinction Characteristics of Wall-stabilized Premixed n-Alkane Cool Flames,”
    13th Asia-Pacific Conference on Combustion (ASPACC), Abu Dhabi, W4-19 (2021).
　　　

2020

  • M. Lee, T. Mizuno, and Y. Suzuki,
    “Investigation of the Wall Chemical Effect on Cool Flames,”
    2020 Korean Institute of Chemical Engineers (KIChE) Fall Meeting International Symposium: e-conference, On-line, Oct. 14-16, (2020). (in Korean)

2019

  • Lee, M., Fan, Y., and Suzuki, Y.,
    “Evaluation of Cool Flame Ignition Temperature on Heated Walls,”
    11th US National Combustion Meeting, Pasadena, WiPP, P33, (2019).
  • Liu, Y., Badel, A., Miyoshi, T., and Suzuki, Y.,
    "Dual-Stage-Electrode-Enhanced Efficient SSHI for Rotational Electret Energy Harvester,"
    20th Int. Conf. Solid-state Sensors, Actuators, and Microsystems (Transducers ’19), Berlin, (2019), W3P.054.
  • Yeh, C.-H., Zhao, X., Qin, Y., Gianchandani, Y., Suzuki, Y., and Morimoto, K.,
    "Deep Electrode and Parylene E-based Capacitive VOC Detector for Micro Gas Chromatograph Application,"
    20th Int. Conf. Solid-state Sensors, Actuators, and Microsystems (Transducers ’19), Berlin, (2019), T3P.036.
  • Guo, J., Fan, Y., Iki, N., and Suzuki, Y.,
    “Evaluation of Wall Chemical Effect in Hydrogen Flame,”
    12nd Asia-Pacific Conference on Combustion (ASPACC), Fukuoka, P396 (2019).
  • Lee M., Fan, Y., Ju, Y., and Suzuki, Y.,
    “Study on Ignition Temperature of Wall-Stabilized Cool Flames,”
    12nd Asia-Pacific Conference on Combustion (ASPACC), Fukuoka, P396 (2019).
  • Kim, S., Suzuki, K., and Suzuki, Y.,
    “Solid State Quantum Chemical Investigation of a High-performance Fluorinated Amorphous Polymer Electret,”
    Invited talk, IEEE 17th Int. Symp. Electrets (ISE17), Limerick, p.23 (2019).
  • Miyoshi, T., Tanaka, Y., and Suzuki, Y.,
    “Development of Rotational Energy Harvester with Bipolar Polymer Electret,”
    IEEE 17th Int. Symp. Electrets (ISE17), Limerick, p.112, (2019).
  • Suzuki, Y., Fan, Y., and Lee, M.,
    “Quantitative Measurement of Near-wall Radicals Using Microscopic Two-photon-absorption Laser Induced Fluorescence (TALIF),”
    Plenary talk, 15th Asian Symposium on Visualization, Busan, PL-2 (2019).
  • Suzuki, Y.,
    “Energy harvesting technologies for powering IoT,”
    Invited talk, Tsukuba Conf., Tsukuba, E05C-1 (2019).
  • Kim, S., Zhang, Y., Suzuki, K., and Suzuki, Y.,
    “Investigation of Charge Stability in Amorphous Fluorinated Polymer Using Quantum Chemical Analysis,”
    IEEE Conf. on Electr. Insul. Dielectr. Phenom. (CEIDP), Richland, 8-1 (2019).
  • Suzuki, Y.,
    “Electret-based Thermal and Kinetic Energy Harvesting for Wearable Devices,”
    Plenary talk, 2nd Pacific Rim Thermal Engineering Conference (PRTEC 2019), Maui, 2PL05 (2019).
  • Lee, M., Mizuno, T., Fan, Y., Ju, Y., and Suzuki, Y.,
    “Wall Effect on Cool Flame Ignition Behavior,”
    2nd Pacific Rim Thermal Engineering Conference (PRTEC 2019), Maui, 24430 (2019).（2019年度日本機械学会熱工学部門講演論文表彰）
  • Miyoshi, T., Tanaka, Y., and Suzuki, Y.,
    “Effect of Natural Frequency of Rotational Electret Energy Harvester for Human Walking,”
    19th Int. Conf. on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2019), Krakow, P2-12 (2019).
  • Kittipaisalsilpa, K., Kato, T., and Suzuki, Y.,
    “Effect of Impurity/Humidity on Liquid-Crystal-Enhanced Electret Vibration Energy Harvester,”
    19th Int. Conf. on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2019), Krakow, T4-B2 (2019).
  • Peng, J., Lee, M., Fan, Y., Yamamoto, A., and Suzuki, Y.,
    “Convection-effect-enhanced Thin Metal Thermoelectric Module Directly-Heated by Catalytic Combustion,”
    19th Int. Conf. on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2019), Krakow, T1-B2 (2019).

2018

  • Miyoshi, T., Adachi, M., Suzuki, K., Liu, Y., and Suzuki, Y.,
    “Low-profile Rotational Electret Generator Using Print Circuit Board for Energy Harvesting from Arm Swing,”
    31th IEEE Int. Conf. Micro Electro Mechanical Systems (MEMS’18), Belfast, pp. 230-232 (2018).
  • Lu, J., and Suzuki, Y.,
    “Soft X-ray-Charged Multilayered Piezoelectret with Embedded Electrode for Push-botton Energy Harvesting,”
    31th IEEE Int. Conf. Micro Electro Mechanical Systems (MEMS’18), Belfast, pp. 646-648 (2018).
  • Zhao, A., Peng, J., Fan, Y., Morimoto, K., and Suzuki, Y., "Boiling heat transfer characteristics of low GWP working fluids at low mass and heat fluxes," 10th Int. Conf. Boiling and Condensation Heat Transfer (ICBCHT), Nagasaki, B1126 (2018).
  • Morimoto, K., Jin, S., and Suzuki, Y., “High-Performance Double-Pipe Turbulent Heat Exchangers with V-Shaped Oblique Wavy Walls,” 9th Int. Symp. Turbulence, Heat and Mass Transfer (THMT’18), Rio de Janeiro, pp. 569-572 (2018).
  • Miyoshi, T., Adachi, M., Tanaka, Y., and Suzuki, Y.,
    ”Low-profile Rotational Electret Energy Harvester for Battery-less Wearable Device,”
    Invited talk, IEEE/ASME Int. Conf. on Advanced Intelligent Mechatronics (AIM 2018), Auckland, TuBT5.6 (2018).
  • Lee, M., Fan, Y., Reuter C.B., Ju, Y., and Suzuki, Y.,
    “DME/Oxygen Wall-Stabilized Premixed Cool Flames,”
    37th Int. Symp. Combustion (Combustion 2018), Dublin, (2018), 1D15.
  • Saiki, Y., Kinefuchi, I., Fan, Y., and Suzuki, Y.,
    “Evaluation of H-atom Adsorption on Wall Surfaces with a Plasma Molecular Beam Scattering Technique,”
    37th Int. Symp. Combustion (Combustion 2018), Dublin, (2018), 1G14.
  • Fan, Y., Saiki, Y., Sanal, S., and Suzuki, Y.,
    “Two-dimensional H-TALIF Measurements and Numerical Simulation of Methane Flame under Wall Radical Quenching,”
    37th Int. Symp. Combustion (Combustion 2018), Dublin, (2018), 2E12.
  • Wan, S., Fan, Y., Maruta, K., and Suzuki, Y.,
    “Wall Chemical Effect of Metal Surfaces on DME/air Cool Flame,”
    37th Int. Symp. Combustion (Combustion 2018), Dublin, (2018), 5H13.
  • Lee, M., Fan, Y., Ju, Y., and Suzuki, Y.,
    “Wall Chemical Effects on Wall-Stabilized Cool Flames”
    37th Int. Symp. Combustion (Combustion 2018), WiPP, Dublin, (2018), 1P087.
  • Fan, Y., Guo, J., Iki, N., and Suzuki, Y.,
    “Investigation of Wall Radical Quenching in Hydrogen Flame for Gas Turbine Applications,”
    37th Int. Symp. Combustion (Combustion 2018), WiPP, Dublin, (2018), 2P225.
  • Fan, Y., Morimoto, K., and Suzuki, Y.,
    “Combustion Characteristics of Mildly Flammable R1234yf in Micro Flow Reactor under Elevated Pressures”
    37th Int. Symp. Combustion (Combustion 2018), WiPP, Dublin, (2018), 4P156.
  • Panklang, N., Techaumnat, B., Wisitsoraat, A., Suzuki, Y.,
    “Separation of Cells and Particles by the Application of Discrete Dielectrophoretic Force,”
    22th Int. Conf. Minituarized Systems for Chemistry and Life Sciences (MicroTAS 2018), Kaohsiung, (2018), T195g.
  • Suzuki, Y., Lee, M., Wan, S., Fan, Y.,
    “Wall Chemical Effect on Cool Flame,”
    15th Int. Conf. Flow Dynamics, Sendai, (2018), OS2-56.
  • Liu, Y., Badel, A., and Suzuki, Y.,
    “Dual-stage Electrode Design of Rotational Electret Energy Harvester for Efficient Self-powered SSHI,”
    18th Int. Conf. on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2018), Daytona Beach, W2B-02 (2018).
  • Lu, Y., and Suzuki, Y.,
    “Push-button Kinetic Energy Harvester with Soft-X-ray-Charged Folded Multilayer Piezoelectret,”
    18th Int. Conf. on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2018), Daytona Beach, W3B-01 (2018) (Best Paper Award Finalist).
  • Kim, S., Suzuki, K., and Suzuki, Y.,
    “Development of A High-performance Amorphous Fluorinated Polymer Electret Based on Quantum Chemical Analysis,”
    18th Int. Conf. on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2018), Daytona Beach, T4B-01 (2018) (Best Paper Award).
  • Tanaka, Y., Miyoshi, T., and Suzuki, Y.,
    “Stochastic Modelling of Human Arm Swing Toward Standard Testing for Rotational Energy Harvester,”
    18th Int. Conf. on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2018), Daytona Beach, T4B-03 (2018).

2017

  • Lee, M., Reuter, C. B., Suzuki, Y., and Ju, Y.,
    “Numerical Study of Wall-stabilized Cool Flames”
    Asian Conf. Therm. Sci., Jeju, ACTS-P00731 (2017) .
  • Kinoshita, H., Suzuki, Y., and Morimoto, K.,
    "Shape Optimization in Conjugate Heat Transfer Problem with Solidification and Wall Heat Conduction,"
    Asian Conf. Therm. Sci., Jeju, ACTS-P00402 (2017) .
  • Kwan, T., Lee, M., Morimoto, K., and Suzuki, Y.,
    "Wall Temperature Measurement in a Visualization Engine Using a Flexible Wireless Sensor,"
    Asian Conf. Therm. Sci., Jeju, ACTS-P00670 (2017) .
  • Oh, S., Morimoto, K., and Suzuki, Y.,
    "Thermal Evaluation of Near-field-enhanced MEMS Radiator with Multi-layered Structure,"
    Asian Conf. Therm. Sci., Jeju, ACTS-P00671 (2017) .
  • Suzuki, Y.,
    “Development of New Electret Charging Methods and Its Application to MEMS Energy Harvesters,”
    Invited talk, Design, Test, Integration & Packaging of MEMS/MOEMS Conf. (DTIP 2017), Bordeaux, France (2017).
  • Kwan, T., Lee, M., Morimoto, K., and Suzuki, Y.,
    “Ｗall Temperature Measurement in a Visualization Engine Using Flexible Wireless Sensor,”
    9th Int. Conf. Modeling and Diagnostics for Advanced Engine Systems (COMODIA 2017), Okayama, A203, (2017).
  • Kim, S., and Suzuki, Y.,
    “Quantum Chemical Study of Charge Trap in Amorphous Perfluoro Polymer Electret,”
    IEEE 16th Int. Symp. Electrets (ISE16), Leuven, p47, (2017).
  • Lu, J., and Suzuki, Y.,
    “Soft X-ray Charged Piezoelectret with Embedded Electrodes,”
    IEEE 16th Int. Symp. Electrets (ISE16), Leuven, p105, (2017).
  • Kinoshita, H., Suzuki, Y., and Morimoto, K.,
    “Meshless-analysis-based Shape Optimization in Conjugate Heat Transfer Problems,”
    9th JSME-KSME Thermal Fluid Eng. Conf. (TFEC9), Okinawa, TFEC9-1407 (2017)
  • Morimoto, K., Goto, Y., and Suzuki, Y.,
    “RANS-based Adjoint Analysis for Shape Optimization of High-performance Turbulent Heat Exchangers,”
    9th JSME-KSME Thermal Fluid Eng. Conf. (TFEC9), Okinawa, TFEC9-1618 (2017)
  • Matsushita, R., Fan, Y., Morimoto, K., and Suzuki, Y.,
    “Heat Transfer Performance of Low-GWP Refrigerants in a Small-Scale Binary-Cycle System,”
    9th JSME-KSME Thermal Fluid Eng. Conf. (TFEC9), Okinawa, TFEC9-1513 (2017)
  • Ro, J., Fan, Y., Morimoto, K., and Suzuki, Y.
    “Reactivity Evaluation of Weak-Combustibility Fluids in Micro Flow Reactor with Streamwise Temperature Gradient,”
    9th JSME-KSME Thermal Fluid Eng. Conf. (TFEC9), Okinawa, TFEC9-1603 (2017)
  • Yeh, C.-H., Suzuki, Y., and Morimoto, K.,
    “MEMS Gas Sensor Using Parylene E and High-Aspect-Ratio Electrode Structure for High-Sensitivity VOC Detection,”
    9th JSME-KSME Thermal Fluid Eng. Conf. (TFEC9), Okinawa, TFEC9-1617 (2017)
  • Xie, H., Morimoto, K., and Suzuki, Y.,
    “Electrostatic Unsteady Thermal Energy Harvesting Using Nematic Liquid Crystal,”
    17th Int. Conf. on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2017), Kanazawa, T2A.3 (2017) (Best Paper Award).
  • Hakamata, K., Miyoshi, T., Itoga, C., Tanaka, Y., and Suzuki, Y.,
    “High-performance Ceramic Electret and Its Application to Vibration Energy Harvesting,”
    17th Int. Conf. on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2017), Kanazawa, PW.55 (2017) (Best Paper Award).
  • Adachi, M., Miyoshi, T., Suzuki, K., Fu, Q., Fang, Q., and Suzuki, Y.,
    “Development of Rotational Electret Energy Harvester Using Print Circuit Board,”
    17th Int. Conf. on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2017), Kanazawa, PMIA.T.5 (2017).
  • Tanaka, Y., Miyoshi, T., and Suzuki, Y.,
    “Modeling of Arm Motion for Rotational Energy Harvester,”
    17th Int. Conf. on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2017), Kanazawa, W1A.2 (2017).
  • Liu, Y., and Suzuki, Y.,
    “Self-powered SSHI for Electret Energy Harvester,”
    17th Int. Conf. on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2017), Kanazawa, W3B.2 (2017).
  • Murotani, K., and Suzuki, Y.,
    “MEMS Electret Energy Harvester with Embedded Bistable Electrostatic Spring for Broadband Response,”
    17th Int. Conf. on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2017), Kanazawa, F1A.1 (2017).
  • Kittipaisalsilpa, K., Kato, T., and Suzuki, Y.,
    “Characterization of Fluorinated Nematic Liquid Crystal for High-power Electret Energy Harvester,”
    17th Int. Conf. on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2017), Kanazawa, F1A.4 (2017).
  • Fan, Y., Saiki, Y., Sanal, S., and Suzuki, Y.,
    “H-TALIF Measurmement for Wall Radical Quenching Modeling in Microscale Combustion,”
    17th Int. Conf. on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2017), Kanazawa, T3B.1 (2017).
  • Suzuki, Y., and Morimoto, K.,
    “Parylene and Its Derivatives as MEMS Materials,”
    Invited talk, 4th Int. Conf. Advanced Electromaterials (ICAE 2017), Jeju, S16-0287 (2017).
  • Wan, S., Fan, Y., and Suzuki, Y.,
    “Investigation of Wall Chemical Effect on Weak Flame with GC and PLIF,”
    11th Asia-Pacific Conference on Combustion (ASPACC), Sydney, P396 (2017) (Young Investigator Award).
  • Lee, M., Fan, Y., Reuter, C. B., Ju, Y., and Suzuki, Y.,
    “Numerical Study and HCHO-PLIF Measurement of Wall-Stabilized Cool Flames,”
    11th Asia-Pacific Conference on Combustion (ASPACC), Sydney, P248 (2017).

2016

  • Kittipaisalsilpa, K., Kato, T., and Suzuki, Y.,
    “Liquid-crystal-enhanced Electret Power Generator,”
    29th IEEE Int. Conf. Micro Electro Mechanical Systems (MEMS’16), Shanghai, pp. 37-40 (2016) .
  • Chen, Y.-C., Morimoto, K., and Suzuki, Y.,
    “Electric Instability of Cassie Droplets on Super-lyophobic Pillar Surface: Pull-in versus Electrowetting,”
    29th IEEE Int. Conf. Micro Electro Mechanical Systems (MEMS’16), Shanghai, pp. 137-140 (2016).
  • Noguchi, Y., Morimoto, K., and Suzuki, Y.,
    “Two-Phase Flow and Heat Transfer in Compact Heat Exchangers with Oblique Wavy Walls,”
    1st Pacific Rim Therm. Eng. Conf. (PRTEC 2016), Hawaii, PRTEC-15159, (2016).
  • Morimoto, K., and Suzuki, Y.,
    “Adjoint-Based Shape Optimization of Extended Heat Transfer Surfaces for Enhanced Solidification Process with Heat Conduction in the Solid Wall,”
    1st Pacific Rim Therm. Eng. Conf. (PRTEC 2016), Hawaii, PRTEC-15161, (2016).
  • Fu, Q., Suzuki, Y.,
    “Vibration Electret Energy Harvester with Tunable Electrode Gap,”
    Asia Pacific Conf. Transducers (APCOT), Kanazawa, 6a2, (2016).
  • Wan, S., Fan, Y., Saiki, Y., Maruta, K., and Suzuki, Y.,
    “Investigation of Wall Chemical Effect on DME Weak Flame in a Rectangular Micro Channel with a Streamwise Temperature Gradient,”
    36th Int. Symp. Combustion (Combustion 2016), Seoul, Work-in-Progress Poster, 1P123 (2016).
  • Wan, S., Fan, Y., Maruta, K., and Suzuki, Y.,
    “HCHO-PLIF Measurement of DME Weak Flame for Investigation of Wall Chemical Effect,”
    36th Int. Symp. Combustion (Combustion 2016), Seoul, Work-in-Progress Poster, 2P138 (2016).
  • Suzuki, Y.,
    “Electret-based Vibration Energy Harvesting: Opportunity for IoT/Wearable Devices,”
    Plenary talk, 5th Int. Conf. Material Science and Engineering Technology (ICMSET 2016), Tokyo (2016).
  • Kim, S., and Suzuki, Y.,
    “MEMS Comb-Drive Electret Energy Harvester Charged after Packaging,”
    IEEE Sensors 2016, Orlando, pp. 1239-1241 (2016).
  • Kim, S., and Suzuki, Y.,
    “Photoelectric-charging-enhanced MEMS Electret Energy Harvester with Vacuum Package,”
    16th Int. Conf. on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2016), Paris, T1A01 (2016).
  • Xie, H., Morimoto, K., and Suzuki, Y.,
    “Electret-based Unsteady Thermal Energy Harvester Using Potassium Tantalate Niobate Crystal,”
    16th Int. Conf. on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2016), Paris, T2B01 (2016).
  • Lu, J., Cho, H., and Suzuki, Y.,
    “Soft X-ray Charged Piezoelectret for Kinetic Energy Harvesting,”
    16th Int. Conf. on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2016), Paris, F1B02 (2016).
  • Chen, Y.-C., Morimoto, K., and Suzuki, Y.,
    “Effect of Pillar Conductivity on the Critical Voltage of Cassie-to-Wenzel Transition,”
    Int. Symp. Micro-Nano Sci. Tech. 2016, Tokyo, SaA1-A-6 (2016).
  • Yeh, C.-H., Suzuki, Y., and Morimoto, K.,
    “Parylene-based MEMS Gas Sensor for High-sensitivity VOC Detection with 3D Electrode Structure,”
    Int. Symp. Micro-Nano Sci. Tech. 2016, Tokyo, SaA1-A-6 (2016).
  • Adachi, M., and Suzuki, Y.,
    “Improved Model of MEMS Rotational Electret Energy Harvester,”
    Int. Symp. Micro-Nano Sci. Tech. 2016, Tokyo, SuP1-A-3 (2016).
  • Kittipaisalsilpa, K., and Suzuki, Y.,
    “Modeling of Liquid-crystal-enhanced Electrostatic Vibration Generator,”
    Int. Symp. Micro-Nano Sci. Tech. 2016, Tokyo, SuP1-A-4 (2016).

2015

  • Chen, Y.-C., Song, K.-Y., Morimoto, K., and Suzuki, Y.,
    “Liquid-Tolerant Electret Using Super-Lyophobic Pillar Surface,”
    28th IEEE Int. Conf. Micro Electro Mechanical Systems (MEMS’15), Estoril, (2015), pp. 1086-1089.
  • Suzuki, Y.,
    "Electret-based Vibration Energy Harvesting for Sensor Network,"
    Invited talk, 18th Int. Conf. Solid-state Sensors, Actuators, and Microsystems (Transducers ’15), Anchorage, (2015), pp. 43-46.
  • Fu, Q., and Suzuki, Y.,
    “In-plane Gap-closing MEMS Vibration Electret Energy Harvester on Thick BOX Layer,”
    18th Int. Conf. Solid-state Sensors, Actuators, and Microsystems (Transducers ’15), Anchorage, (2015), pp. 1925-1928.
  • Wan, S., Fan, Y., Maruta, K., and Suzuki, Y.,
    “Wall Chemical Effect on DME Weak Flame in a Rectangular Micro Channel with a Streamwise Temperature Gradient,”
    10th Asia-Pacific Conference on Combustion (ASPACC), Beijing, (2015), ID.295.
  • Nita, S., Wang, J., Minh, D. Q., Chen, Y.-C., Suzuki, Y., Amberg, G., Shiomi, J.,
    "Controlling Dynamic Wetting by Surface Charges and Microstructures,"
    ASME 2015 Int. Tech. Conf. Exhibition Packaging and Integration of Electronic and Photonic Microsystems (InterPACK)/Int. Conf. Nanochannels, Microchannels and Minichannels (ICNMM), InterPACK/ICNMM2015-48762 (2015).
  • Suzuki, Y.,
    “Electret Energy Harvesting,”
    Invited talk, 10th Energy Harvesting Workshop, Blacksburg (2015).
  • Suzuki, Y.,
    “Micro Energy - Crossroad between thermal engineering and MEMS technology,”
    Keynote talk, 8th Int. Symp. on Turbulence, Heat and Mass Transfer, Sarajevo, pp. 75-86 (2015).
  • Buranapong, J., Pimpin, A., Srituravanich, W., and Suzuki, Y.,
    "A Microfluid Chip Coupled with Magnetophoretic and Dielectrophoretic Forces for Separating Malaria-infected Red Blood Cells,"
    19th Int. Conf. Miniaturised Systems for Chemistry and Life Sciences (MicroTAS 2015), Gyeongju, T.017a, (2015).
  • Lee, M., Morimoto, K., and Suzuki, Y.,
    "Evaluation of Non-contact Wall Temperature Measurement Using MEMS Wireless Sensor,"
    SAE Paper 2015-01-1997 (2015).
  • Lee, M., Morimoto, K., and Suzuki, Y.,
    “Flexible Wireless Wall Temperature Sensor for Unsteady Thermal Field,”
    15th Int. Conf. on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2015), Boston, W3B-02 (2015).
  • Nakajima, H., Oh, S., Ueno, A., Morimoto, K., and Suzuki, Y.,
    “Development of Near-Field-Enhanced High-Fill-Factor MEMS Radiator with Shared Springs,”
    15th Int. Conf. on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2015), Boston, F7B-03 (2015).
  • Nakano, J., Komori, K., and Hattori, Y., and Suzuki, Y.,
    “MEMS Rotational Electret Energy Harvester for Human Motion,”
    15th Int. Conf. on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2015), Boston, F8A-03 (2015).(Best Paper Award).

2014

  • Fu, Q., and Suzuki, Y.,
    “MEMS Vibration Electret Energy Harvester with Combined Electrodes,”
    27th IEEE Int. Conf. Micro Electro Mechanical Systems (MEMS’14), San Francisco, (2014), pp. 409-412.
  • Feng, Y., and Suzuki, Y.,
    “All-polymer Piezoeelctret Energy Harvester with Embedded PEDOT Electrode,”
    27th IEEE Int. Conf. Micro Electro Mechanical Systems (MEMS’14), San Francisco, (2014), pp. 374-377.
  • Suzuki, Y., and Saiki, Y.,
    “Microscale Combustion: Surface Effect on Gas-phase Reaction,”
    Plenary talk, Int. Conf. Heat Trans. Fluid Flow in Microscale (HTFFM-V), Marseille, (2014).
  • Song, K.-Y., Morimoto, K., and Suzuki, Y.,
    “Investigation of Cassie-to-Wenzel Transition of Liquid Droplets on MEMS-based Pillared Surface,”
    7th Asia-Pacific Conference on Transducers and Micro/Nano Technologies, Daegu, (2014).
  • Saiki, Y., and Suzuki, Y.,
    “Radical Quenching on Metal Surface in a Methane-air Premixed Flame,”
    35th Int. Symp. Combustion (Combustion 2014), San Francisco, (2014), 5G01.
  • Lin, W., Wan, S., and Suzuki, Y.,
    “PLIF Measurement of OH Generated with Pulsed Arc Discharge for Radical Quenching Study,”
    35th Int. Symp. Combustion (Combustion 2014), Work-in-Progress Poster, San Francisco, (2014), W1P053.
  • Lee, M., and Suzuki, Y.,
    “Non-contact Wall Temperature Measurement Using MEMS Wireless Sensor,”
    35th Int. Symp. Combustion (Combustion 2014), Work-in-Progress Poster, San Francisco, (2014), W4P036.
  • Suzuki, Y.,
    “Energy Harvesting using Electrets,”
    Invited talk, Workshop on Dielectrics for Energy Harvesting and Storage Applications, Baltimore, (2014).
  • Fu, Q., and Suzuki, Y.,
    “Development of Micron-gap Electret Charged with Soft X-ray and Its Application to Vibration Energy Harvesting,”
    IEEE 15th Int. Symp. Electrets (ISE15), Baltimore, (2014).
  • Feng, Y., and Suzuki, Y.,
    “Trench-filled Cellular Parylene Electret with Embedded Electrode for Vibration Energy Harvesting,”
    IEEE 15th Int. Symp. Electrets (ISE15), Baltimore, (2014).
  • Chen, R., and Suzuki, Y.,
    “Effect of Oxygen Plasma Etching on the Performance of CYTOP Electret,”
    IEEE 15th Int. Symp. Electrets (ISE15), Baltimore, (2014).
  • Ueno, A., and Suzuki, Y.,
    “Thermal Radiation Characteristics in Sub-micron Region for MEMS Space Radiator,”
    15th Int. Heat Transfer Conf., Kyoto, IHTC15-9636/RAD-J-323 (2014).
  • Morimoto, K., and Suzuki, Y.,
    “Adjoint-Based Optimum Thermal Control of Laser Diodes,”
    15th Int. Heat Transfer Conf., Kyoto, IHTC15-9636/OPT-F-522 (2014).
  • Fu, Q., and Suzuki, Y.,
    “A Design Method of In-plane MEMS Electret Energy Harvester with Comb Drives,”
    14th Int. Conf. on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2014), Awaji, (2014). Also, J. Phys.: Conf. Ser., Vol. 557, No. 012011 (2014).
  • Kim, S., Fu, Q., Hagiwara, K., and Suzuki, Y.,
    “Development of A Pre-packaged MEMS Electret Energy Harvester Before Charging,”
    14th Int. Conf. on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2014), Awaji, (2014). Also, J. Phys.: Conf. Ser., Vol. 557, No. 012063 (2014).
  • Lee, M., Kawahara, Y., Morimoto, K., and Suzuki, Y.,
    “MEMS Wireless Temperature Sensor for Combustion Studies,”
    14th Int. Conf. on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2014), Awaji, (2014).

2013

2012

  • Kim, M., Ito, S., Morimoto, K., and Suzuki, Y.,
    “Optimum Temperature Control of Micro Devices Under High-speed Thermal Disturbances,”
    25th IEEE Int. Conf. Micro Electro Mechanical Systems (MEMS’12), Paris, (2012), pp. 1085-1088.
  • Feng, Y., Hagiwara, K., Iguchi, Y., and Suzuki, Y.,
    “Trench-filled Cellular Parylene Structure for Piezoelectric Polymer Electret,”
    25th IEEE Int. Conf. Micro Electro Mechanical Systems (MEMS’12), Paris, (2012), pp. 1189-1192.
  • Takada, M., Morimoto, K., Suzuki, Y., and Ikoma, K.,
    “Effect of Fuel Supply on Pressure Increase of Anode Gas Recirculation Supersonic Ejector for SOFC,”
    8th KSME-JSME Thermal and Fluids Engineering Conf., Incheon, (2012), FR07-003, 4pp.
  • Fukumoto, K., Morimoto, K., and Suzuki, Y.,
    “MEMS-based Superhydrophobic Surface for High-speed droplet Manipulation,”
    8th KSME-JSME Thermal and Fluids Engineering Conf., Incheon, (2012), FR09-005, 4pp.
  • Sakata, K., Tagomori, K., Sugiyama, N., Takenouchi, M., Shinya, Y., and Suzuki, Y.,
    “Development of Nano-Porous Alumina Catalyst Support by Anodic Oxidation of Thermally and Kinetically Sprayed Aluminum Coatings,”
    Int. Thermal Spray 2012 Conf. and Expo. (ITSC2012), Houston, (2012), pp. 287-291.
  • Ueno, A., and Suzuki, Y.,
    “Near-field-effect-enhanced Micro Radiator Array for Active Control of Thermal Radiation,”
    Int. Workshop Nano-Micro Thermal Radiation (NanoRad 2012), Matsushima bay area, (2012), pp. 72-75.
  • Suzuki, Y.,
    “MEMS Electret Generator for Energy Harvesting: Material, Design and Evaluation,”
    Invited talk, 6th Asia-Pacific Conf. Transducers and Micro-Nano Technology (APCOT 2012), Nanjing, (2012).
  • Minakawa, Y., and Suzuki, Y.,
    “X-shaped High-aspect-ratio Parylene Spring for Low-resonant-frequency MEMS Electret Energy Harvester,”
    6th Asia-Pacific Conf. Transducers and Micro-Nano Technology (APCOT 2012), Nanjing, (2012), ac12000235.
  • Saiki, Y., and Suzuki, Y.,
    "Effect of Wall Surface Reaction on a Methane-Air Premixed Flame in Narrow Channels with Different Wall Materials,"
    34rd Int. Symp. Combustion (Combustion 2012), Warsaw, Poland, July 29-August 3, (2012), 2F11.
  • Lin, W., and Suzuki, Y.
    "Investigation of Chemical Quenching Mechanism on Metal Surfaces based on PLIF Measurement of OH Generated with Pulsed Arc Discharge,"
    34rd Int. Symp. Combustion (Combustion 2012), Warsaw, Poland, July 29-August 3, (2012),Work-in-progress Poster, W1P058.
  • Suzuki, Y.,
    “Nano-particle-enhanced High-performance Polymer Electret for Vibration Energy Harvesting,”
    Keynote talk, IUMRS Int. Conf. Electr. Materials (IUMRS-ICEM2012), Yokoyama, (2012), B-7K24-005.
  • Feng, Y., Hagiwara, K., Iguchi, Y., and Suzuki, Y.,
    “MEMS-based Cellular Parylene Structure for Piezoelectric Polymer Electret,”
    IUMRS Int. Conf. Electr. Materials (IUMRS-ICEM2012), Yokoyama, (2012), B-7O24-006.
  • Morimoto, K., Fukumoto, K., and Suzuki, Y.,
    “MEMS-based Pillared Surface for High-speed Dropet Manipulation: Failure of Cassie-Baxter Model,”
    Proc. 16th Int. Conf. Miniaturised Systems for Chemistry and Life Sciences (MicroTAS 2012), Okinawa, (2012), pp. 64-66.
  • Chen, R., and Suzuki, Y.,
    “Metal-On-Nothing Electrodes for Reducing Parasitic Capacitance in Electret Energy Harvesting Devices,”
    Proc. 12th Int. Workshop on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2012), Atlanta, (2012), pp. 121-124.
  • Minakawa, Y., and Suzuki, Y.,
    “Low-resonant-frequency MEMS Electret Energy Harvester with X-Shaped High-aspect-ratio Parylene Spring,”
    Proc. 12th Int. Workshop on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2012), Atlanta, (2012), pp. 133-136.

2011

2010

2009

  • Hashimoto, S., Nishimura, T., Miwa, J., Suzuki, Y., and Kasagi, N.,
    "Label-free Continuous Micro Cell Sorter with Antibody-immobilized Oblique Grooves,"
    22nd IEEE Int. Conf. Micro Electro Mechanical Systems (MEMS2009), Sorrento, Italy, January 26-29, 2009, pp. 60-63.
  • Kamezawa, C., Suzuki, Y., and Kasagi, N.,
    "Mechanical Response Evaluation of High-thermally-stable-grade Parylene Spring,"
    22nd IEEE Int. Conf. Micro Electro Mechanical Systems (MEMS2009), Sorrento, Italy, January 26-29, 2009, pp. 615-618.
  • Edamoto, M., Suzuki, Y., Kasagi, N., Kashiwagi, K., Morizawa, Y., Yokoyama, T., Seki, T., and Oba, M.,
    "Low-resonant-frequency Micro Electret Generator for Energy Harvesting Application,"
    22nd IEEE Int. Conf. Micro Electro Mechanical Systems (MEMS2009), Sorrento, Italy, January 26-29, 2009, pp. 1059-1062.
  • Miki, D., Suzuki, Y., and Kasagi, N.,
    "Effect of Nonlinear External Circuit on Electrostatic Force of Micro Electret Generator,"
    15th Int. Conf. Solid-state Sensors, Actuators, and Microsystems (Transducers' 09), Denver, 2009.6.21-25, pp. 636-639.
  • Okochi, S., Kasagi, N., Suzuki, Y ., and Ito, S.,
    "Development of Micro Plasma Actuator for Active Flow Control,"
    7th World Conf. Exp. Heat Transfer, Fluid Mech. and Thermodyn., Krakow, Poland, June 28-July 03, 2009, pp. 1741-1748.
  • Saiki, Y., Suzuki, Y., and Kasagi, N.,
    "Active Control of Swirling Coaxial Jet Mixing with Manipulation of Large-scale Vortical Structures,"
    Turbulence, Heat and Mass Transfer 6, K. Hanjalic et al. Ed., Begell House, 6th Int. Symp. Turbulence, Heat and Mass Transfer, Rome, Italy, Sept. 14-18, 2009 (CD-ROM), 12 pp.
  • Wu, T., Suzuki, Y., and Kasagi, N.,
    "Design and Microfabrication of High Peformance Super-Lyophobic Surfaces,"
    13th Int. Conf. Miniaturized Systems for Chemistry and Life Sciences (MicroTAS 2009), Jeju, Nov. 1-5, 2009, pp. 773-775.
  • Inokuchi, H., Suzuki, Y., and Kasagi, N.,
    "Micro Magnetic Cell Sorting System with a Function of Continuous Labeling and Separation,"
    13th Int. Conf. Miniaturized Systems for Chemistry and Life Sciences (MicroTAS 2009), Jeju, Nov. 1-5, 2009, pp. 1877-1879.
  • Kirikae, D., Suzuki, Y., and Kasagi, N.,
    "Emission Spectral Control Using Metal-coated Silicon Microcavity for Thermophotovoltaic,"
    9th Int. Workshop on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2009), Washington DC, USA, Dec. 1-4, 2009, pp.161-164.
  • Miki, D., Honzumi, M., Suzuki, Y., and Kasagi, N.,
    "MEMS Electret Generator with Electrostatic Levitation,"
    9th Int.Workshop on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2009), Washington DC, USA, Dec. 1-4, 2009, pp.169-172.
  • Hagiwara, K., Honzumi, M., Goto, M., Tajima, T., Yasuno, Y., Kodama, H., Kidokoro, K., Kashiwagi, K., and Suzuki, Y.,
    "Novel Through-substrate Charging Method for Electret Generator Using Soft X-ray Irradiation,"
    9th Int. Workshop on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2009), Washington DC, USA, Dec. 1-4, 2009, pp.173-176.

2008

  • Tsurumi, Y., Suzuki, Y., and Kasagi, N.,
    "Non-Contact Electrostatic Micro-Bearing Using Polymer Electret,"
    21st IEEE Int. Conf. Micro Electro Mechanical Systems (MEMS2008), Tucson, Arizona, January 13-17, 2008, pp. 511-514.
  • Wu, T., Suzuki, Y., and Kasagi, N.,
    "Electrostatic Droplet Manipulation Using Electret as a Voltage Source,"
    21st IEEE Int. Conf. Micro Electro Mechanical Systems (MEMS2008), Tucson, Arizona, January 13-17, 2008, pp. 591-594.
  • Kamezawa, C., Suzuki, Y., and Kasagi, N.,
    "In-situ Strain Monitoring of Micromachined Parylene Spring for Fatigue Test,"
    4th Asia-Pacific Conference on Transducers and Micro-Nano Technology (APCOT 2008), Tainan, Taiwan, June 22-25, 2008, 2D1-1, 4pp.
  • Edamoto, M., Suzuki, Y., and Kasagi, N.,
    "Electret-based Energy Harvesting Device with Parylene Flexible Springs,"
    4th Asia-Pacific Conference on Transducers and Micro-Nano Technology (APCOT 2008), Tainan, Taiwan, June 22-25, 2008, 2B3-1, 4pp.
  • Fan, Y., Suzuki, Y., and Kasagi, N.,
    "Experimental Study of Micro-scale Premixed Flame in Quartz Channels,"
    32nd Int. Symp. Combustion (Combustion 2008), Montreal, Canada, August 3-8, 2008, p. 18, 1E09.
  • Kamijo, T., Suzuki, Y., Kasagi, N., and Okamasa, T.,
    "High-temperature Micro Catalytic Combustor with Pd/Nano-porous Alumina,"
    32nd Int. Symp. Combustion (Combustion 2008), Montreal, Canada, August 3-8, 2008, p. 57, 2C05.
  • Sakane, Y., Suzuki, Y., and Kasagi, N.,
    "Development of High-performance Purfluorinated Polymer Electret,"
    13th Int. Symp. Electrets, Tokyo, September 15-17, 2008, p. 13.
  • Suzuki, Y., Edamoto, M., Kasagi, N., Kashiwagi, K., and Morizawa, Y.,
    "Micro Power Generator with High-performace Polymer Electret,"
    13th Int. Symp. Electrets, Tokyo, September 15-17, 2008, p. 53.
  • Kamijo, T., Suzuki, Y., and Kasagi, N.,
    "Micro Catalytic Combustor with Pd/Nano-porous Alumina for High-Temperature Application"
    7th JSME-KSME Thermal Fluids Engineering Conference (TFEC-7), Sapporo, Japan, October 13-16, 2008, Paper No. C124, 2pp.
  • Fan, Y., Suzuki, Y., and Kasagi, N.,
    "On Flame-Wall Thermal-Coupling in Micro Combustors,"
    7th JSME-KSME Thermal Fluids Engineering Conference (TFEC-7), Sapporo, Japan, October 13-16, 2008, Paper No. C125, 2pp.
  • Wu, T., Suzuki, Y. and Kasagi, N.,
    "Modeling for Droplet Manipulation Based on "L-DEP on Electret,"
    25th Sensor Symp., Okinawa, Japan, October 22-24, 2008, pp. 785-786.
  • Inokuchi, H., Suzuki, Y. and Kasagi, N.,
    "Development of Micro Immuno-Magnetic Cell Sorting System with Lamination Mixer and Magnetic Separator,"
    25th Sensor Symp., Okinawa, Japan, October 22-24, 2008, pp. 851-852.
  • Nishimura, T., Miwa, J., Hashimoto, S., Suzuki, Y. and Kasagi, N.,
    "Flow-Through Cell Separation Using Antigen-Antibody Interaction Between Cell and Wall Surface,"
    25th Sensor Symp., Okinawa, Japan, October 22-24, 2008, pp. 853-854.
  • Suzuki, Y.,
    "Energy Harvesting from Vibration Using Polymer Electret,"
    IEEE Int. Symp. Micro-NanoMechatoronics and Human Science (MHS2008), Nagoya, Japan, November 8, 2008, Invited talk, pp. 180-183.
  • Suzuki, Y., Edamoto, M., Kasagi, N., Kashiwagi, K., Morizawa, Y., Yokoyama, T., Seki, T., and Oba, M.,
    "Micro Electret Energy Harvesting Device with Analogue Impedance Conversion Circuit,"
    8th Int. Workshop on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2008), Sendai, Japan, November 9-12, 2008, pp. 7-10.
  • Kirikae, D., Suzuki, Y., and Kasagi, N.,
    "Effect of Microcavity Profile on the Selective Emitter Performance for Thermophotovoltaic,"
    8th Int. Workshop on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2008), Sendai, Japan, November 9-12, 2008, pp. 369-372.
  • Fan, Y., Suzuki, Y., and Kasagi, N.,
    "Ultra-Thin Quartz Combustors for TPV Power Generation,"
    8th Int. Workshop on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2008), Sendai, Japan, November 9-12, 2008, pp. 433-436.

2007

2006

  • Tsutsumino, T., Suzuki, Y., Kasagi, N., Sakane, Y.,
    "Seismic Power Generator Using High-Performance Polymer Electret,"
    19th IEEE Int. Conf. Micro Electro Mechanical Systems (MEMS2006), Istanbul, Jan. 2006, pp.98-101.
  • Miwa, J., Suzuki, Y., and Kasagi, N.,
    "Evaluation of Cell Velocity Regulation in a Microfabricated Adhesion-Based Cell Separation Device,"
    Int. Conf. Microtechnologies in Medicine and Biology, Okinawa, Japan, May 9-12, 2006, pp. 101-104.
  • Inokuchi, H., Nagae, K., Suzuki, Y., Kasagi, N., and Shikazono, N.,
    "Evaluation of Lamination Micro Mixer for Micro Immunomagnetic Cell Sorter,"
    Int. Conf. Microtechnologies in Medicine and Biology, Okinawa, Japan, May 9-12, 2006, pp. 131-134.
  • Saiki, Y., Suzuki, Y., and Kasagi, N.,
    "The Structure of a Bluff-body Held Flame Controlled by Arrayed Micro Actuators,"
    17th Int. Symp. Transport Phenomena, Toyama, September 4-8, 2006, Paper No. 2-D-II-4
  • Suzue Y., Morimoto K., Shikazono N., Suzuki Y. and Kasagi N.,
    "High Performance Heat Exchanger with Oblique-Wave Walls,"
    13th International Heat Transfer Conf., August 13-18, Sydney, Australia, HEX-24.
  • Kasagi, N., Fukagata, K., and Suzuki, Y.,
    Plenary Lecture: "Toward feedback control of wall turbulence for skin friction,"
    Conf. on Active Flow Control, Berlin Germany, September 27-29, 2006 (CD-ROM), 19 pp.
  • Tsutsumino, T., Suzuki, Y., Kasagi, N., Kashiwagi, K. and Morizawa, Y.,
    "Micro Seismic Electret Generator for Energy Harvesting,"
    5th Int. Workshop on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2006), Berkeley, pp. 279-282.
  • Okamasa, T., Suzuki, Y. and Kasagi, N.,
    "Non-uniform Heat Generation in Micro Catalytic Combustor,"
    5th Int. Workshop on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2006), Berkeley, pp. 21-24.

2005

  • Suzuki, Y., Yoshino, T., Yamagami, T., and Kasagi, N.,
    Plenary Lecture, "Drag redcution in a turbulent channel flow by using a GA-based feedback control system,"
    6th Symp. Smart Control of Turbulence, March 6-9, 2005, Tokyo, pp. 31-40.
  • Yamagami, T., Suzuki, Y., and Kasagi, N.,
    "Development of feedback control system of wall turbulence using MEMS devices,"
    6th Symp. Smart Control of Turbulence, March 6-9, 2005, Tokyo, pp. 135-141.
  • Iwamoto, K., Kasagi, N., and Suzuki, Y.,
    "Direct numerical simulation of turbulent channel flow at Reτ = 2320,"
    6th Symp. Smart Control of Turbulence, March 6-9, 2005, Tokyo, pp. 327-333.
  • Morimoto, K., Suzuki, Y., and Kasagi, N.,
    "Optimal shape design of recuperators with oblique wavy walls,"
    6th KSME-JSME Thermal and Fluids Engineering Conf., March 20-23, 2005, Jeju, Korea (CD-ROM), Paper DD.02, 4 pp.
  • Angele, K. P.,Kurimoto, N., Suzuki, Y., and Kasagi, N.,
    "Three-dimensional vortical structures in a coaxial jet manipulated with micro-actuators,"
    6th World Conf. Experimental Heat Transfer, Fluid Mechanics and Thermodynamics, April 17-21, Matsushima, Japan (CD-ROM), Paper 9-b-10, 7 pp.
  • Yen T.-H., Suzuki, Y., and Kasagi, N.,
    "Modeling on Convective Boiling Heat transfer in a micro tube based on Flow visualization,"
    6th World Conf. Experimental Heat Transfer, Fluid Mechanics and Thermodynamics, April 17-21, Matsushima, Japan (CD-ROM), Paper 4-a-9, 6 pp.
  • Kasagi, N., Fukagata, K. and Suzuki, Y.,
    Keynote Lecture, "Adaptive control of wall-turbulence for skin friction drag reduction and some consideration for high Reynolds number flows,"
    2nd Int. Symp. on Seawater Drag Reduction, Busan, Korea, May 2005, pp. 17-32.
  • Yen, T.-H., Shoji, M., Takemura, F., Suzuki, Y., and Kasagi, N.,
    "Visualization of Convective Boiling Heat Transfer in Single Micro-Conduits with Different Shapes of Cross Sections,"
    3rd Int. Conf. Microchannels and Minichannels (ICMM2005), Toronto, Ontario, Canada, June 13-15, 2005 (CD-ROM), Paper No. ICMM2005-75228, 8 pp.
  • Suzuki, Y., Yoshino, T., Yamagami, T., and Kasagi, N.,
    "GA-based feedback control system for drag reduction in turbulent channel flow,"
    4th Int. Symp. Turbulence and Shear Flow Phenomena (TSFP-4), Williamsburg, Virginia, June 27-29, 2005, pp. 301-306.
  • Fukagata, K., Kasagi, N., and Suzuki, Y.,
    "Feedback control system for friction drag reduction in wall-turbulence"
    1st Int. Closed-Loop Flow Control Workshop, Jackson Hole, Wyoming, July 18-19, 2005.
  • Miwa, J., Tan, W. H., Suzuki, Y., Kasagi, N., Shikazono, N., Furukawa, K. and Ushida, T.,
    "Development of micro immunoreaction-based cell sorter for regenerative medicine,"
    1st Int. Conf. BNI Fusion, Marina del Rey, CA, USA, Jul. 20-22, 2005.
  • Morimoto, K., Suzuki, Y., and Kasagi, N.,
    "Optimal Shape Design of Counter-Flow Primary Surface Recuperators,"
    5th Int. Conf. Enhanced, Compact and Ultra-Compact Heat Exchangers, Whistler, BC, Canada, Sep. 11-16, 2005 (CD-ROM), Paper CHE2005-17, pp. 124-131.
  • Miwa, J., Suzuki, Y. and Kasagi, N.,
    "Adhesion-Based Cell Velocity Regulation in an Antibody-Coated Micro Column for Stem Cell Separation,"
    9th Int. Conf. Miniaturised Systems for Chemistry and Life Sciences (μTAS2005), Boston, MA, USA, Oct. 9-13, 2005, pp. 868-870.
  • Inokuchi, H., Suzuki, Y., Kasagi, N., Shikazono, N., Furukawa, K., and Ushida, T.,
    "Micro Magnetic Separator for Stem Cell Sorting System,"
    22nd Sensor Symp., Tokyo, Oct. 20-21, 2005, pp. 125-128.
  • Angele, K.P., Suzuki, Y., Miwa, J., Kasagi, N. and Yamaguchi, Y.
    "Development of a High-speed Scanning Micro-PIV system,"
    6th Int. Symp. Particle Image Velocimetry, (PIV'05), Pasadena, California, USA, September 21-23, 2005.
  • Tsutsumino, T., Suzuki, Y., Kasagi, N., and Tsurumi, Y.
    "High-Performance Polymer Electret for Micro Seismic Generator,"
    5th Int. Workshop on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2005), Tokyo, Nov. 28-30, 2005, pp. 9-12.
  • Fan, Y., Suzuki, Y., and Kasagi, N.,
    "Development of Large-entrainment-ratio Micro Ejector for Catalytic Combustor,"
    5th Int. Workshop on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2005), Tokyo, Nov. 28-30, 2005, pp. 132-135.
  • Okamasa, T., Lee, G.-G., Suzuki, Y., and Kasagi, N.,
    "Development of Micro Catalytic Combustor Using Ceramic Tape Casting,"
    5th Int. Workshop on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2005), Tokyo, Nov. 28-30, 2005, pp. 206-209.

-2004

  • Suzuki, Y., Horii, Y., Kasagi, N., and Matsuda, S.,
    "Micro catalytic combustor with tailored porous alumina,"
    17th IEEE Int. Conf. Micro Electro Mechanical Systems (MEMS2004), Jan. 2004, Maastricht, pp. 312-315.
  • Pimpin, A., Suzuki, Y., and Kasagi, N.,
    "Micro electrostrictive actuator with metal compliant electrodes for flow control applications,"
    17th IEEE Int. Conf. Micro Electro Mechanical Systems (MEMS2004), Jan. 2004, Maastricht, pp. 478-481.
  • Park, J., Yoshino, T., Yamagami, T., Suzuki, Y. and Kasagi, N.,
    "Development of GA-based Evolved System for Feedback Control of Turbulence,"
    5th Symp. on Smart Control of Turbulence, Feb./March 2004, Tokyo, pp. 111-117.
  • Iwamoto, K., Fukagata, K., Kasagi, N. and Suzuki, Y.,
    "DNS of turbulent channel flow at Re_tau=1160 and evaluation of feedback control at practical Reynolds numbers,"
    5th Symp. on Smart Control of Turbulence, Feb./March 2004, Tokyo, pp. 119-125.
  • Yen, T.-H., Kasagi, N. and Suzuki, Y.,
    "Effects of fluid properties and system pressure on convective boiling in microtubes,"
    1st Int. Symp. on Micro & Nano Technology, March 2004, Honolulu, Hawaii (CD-ROM), Paper VII-1-03, 6 pp.
  • Kurimoto, N., Suzuki, Y. and Kasagi, N.,
    "Coaxial Jet Control for Lifted Flame Stabilization with Arrayed Miniature Actuators,"
    12 th Int. Symp. Applications of Laser Techniques to Fluid Mechanics, July 2004, Lisbon, CD-ROM publication, 30-2, 12 pp.
  • Tan, W.-H., Suzuki, Y., Kasagi, N., Shikazono, N., Furukawa, K., and Ushida, T.,
    "Development of Novel Micro Mixer and Its Application to μ-Immunomagnetic Cell Sorter,"
    8th Int. Conf. Miniaturised Systems for Chemistry and Life Sciences (μTAS2004), Malmö, Sweden, (2004), Vol. 1, pp. 156-158.
  • Iwamoto, K., Kasagi, N., and Suzuki, Y.,
    "Dynamical Roles of Large-Scale Structures in Turbulent Channel Flow,"
    WCCM VI in conjunction with APCOM'04, Sept. 5-10, 2004, Beijing, China, MS022-174.
  • Iwamoto, K., Kasagi, N., and Suzuki, Y.,
    "DNS of Moderately High Reynolds Number Turbulent Channel Flow,"
    2nd Int. Workshop on Wall-Bounded Turbulent Flows, Nov. 2-5, 2004, Trieste, Italy.
  • Angele, K., Kurimoto, N., Suzuki, Y., and Kasagi, N.,
    "Active mixing control in a coaxial-jet"
    Bull. Am. Phys. Soc., Vol. 49, No. 9 (2004), p. 53.
  • Yen, T.-H., Suzuki, Y., and Kasagi, N.,
    "Visualization of convective boiling in a micro tube with simultaneous measurement of local heat transfer,"
    1st Int. Forum Heat Transfer, November 2004, Kyoto, pp. 119-120.
  • Arakawa, Y., Suzuki, Y., and Kasagi, N.,
    "Micro seismic power generator using electret polymer film,"
    4th. Int. Workshop on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (Power MEMS 2004), November 28 -30, 2004, Kyoto, pp. 187-190.
  • Suzuki, Y.,
    "Flow visualization of microscale flow boiling and development of micro reactor,"
    Int. Symp. on Micro/Nano Thermal and Fluids Systems, Int. Symp. Series on Mechanical Systems Innovation, December 6-7, 2004, Tokyo.
  • Yoshino, T., Suzuki, Y., Kasagi, N. and Kamiunten, S.,
    "Optimum Design of Micro Thermal Flow Sensor and Its Evaluation in Wall Shear Stress Measurement, "
    16th IEEE Int. Conf. Micro Electro Mechanical Systems (MEMS2003), Jan. 2003, Kyoto, pp. 193-196.
  • Suzuki, Y. and Tai, Y.-C.,
    "Micromachined high-aspect-ratio Parylene beam and its application to low-frequency seismometer,"
    16th IEEE Int. Conf. Micro Electro Mechanical Systems (MEMS2003), Jan. 2003, Kyoto, pp. 486-489.
  • Boland, J., Chao, C.-H., Suzuki, Y. and Tai, Y.-C.,
    "Micro electret power generator, "
    16th IEEE Int. Conf. Micro Electro Mechanical Systems (MEMS2003), Jan. 2003, Kyoto, pp. 538-541.
  • Suzuki, Y., Yoshino, T. and Kasagi, N.,
    "Evaluation of a GA-based freedback control system with arrayed micro sensors and actuators in a turbulent channel flow,"
    4th Symp. on Smart Control of Turbulence, Mar. 2003, Tokyo, pp. 115-122.
  • Yoshino, T., Suzuki, Y., and Kasagi, N.,
    "Evaluation of GA-based feedback control system for drag reduction in wall turbulence,"
    3rd Int. Symp. on Turbulence and Shear Flow Phenomena, Sendai, June 2003, pp. 179-184.
  • Suzuki, Y., Saito, J., and Kasagi, N.,
    "Micro Catalytic Combustor with Pt/Al2O3 Thin Films,"
    7th Int. Conf. Microreaction Technology, Lausanne, September 2003, LMP7.
  • Kasagi, N., Shikazono, N., Suzuki, Y. and Oku, T.,
    "Assessment of High-Performance Micro Bare-Tube Heat Exchangers for Electronic Equipment Cooling,"
    1st Int. Symp. on Process Intensification and Miniaturization, Univ. of Newcastle upon Tyne, UK, Aug. 2003, CD-ROM publication, 6pp.
  • Kasagi, N., Suzuki, Y., Shikazono, N. and Oku, T.,
    "Optimal Design and Assessment of High Performance Micro Bare-Tube Heat Exchangers,"
    4th Int. Conf. on Compact Heat Exchangers and Enhancement Technologies for the Process Industries, Crete Island, Greece, Sep. 27- Oct. 3 2003, pp. 241-246.
  • Iwamoto, K., Kasagi, N. and Suzuki, Y.,
    "Hierarchical Clustering Structures in Turbulent Channel Flow at Re_tau = 1160,"
    Bull. Am. Phys. Soc., Vol. 48, No. 10, Nov. 2003, p. 217.
  • Suzuki, Y., Saito, J., Horii, Y., and Kasagi, N.,
    "Development of micro catalytic combustor with Pt-Al2O3 thin films,"
    Int. Symp. Micro-Mechanical Engineering (ISMME 2003), Tsuchiura, December 1-3, 2003, pp. 171-176.
  • Suzuki, Y., Horii, Y., and Kasagi, N.,
    "Micro catalytic combustor with tailored Pt/Al2O3 films,"
    3rd. Int. Workshop on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (Power MEMS 2003), Makuhari, Dec. 2003, pp. 23-26.
  • Morimoto, K., Iwamoto, K., Suzuki, Y., and Kasagi, N.,
    "Genetic Algorithm-Based Optimization of Feedback Control Scheme for Wall Turbulence, "
    3rd Symp. Smart Control of Turbulence, Mar. 2002, Tokyo, pp. 107-113.
  • Yoshino, T., Tsuda, M., Suzuki, Y., and Kasagi, N.,
    "Toward Development of Feedback Control System for Wall Turbulence with MEMS Sensors and Actuators, "
    3rd Symp. Smart Control of Turbulence, Mar. 2002, Tokyo, pp. 115-120.
  • Suzuki, Y., and Tai, Y.-C.,
    "Micromachined High-aspect ratio Parylene Beam for Soft Spring Applications,"
    2002 Solid State Sensor, Actuator and Microsystems Workshop, 2002, Hilton Head.
  • Yen, T. H., Kasagi, N., and Suzuki, Y.,
    "Forced Convective Boiling Heat Transfer in Microtubes at Low Mass and Heat Fluxes,"
    Symp. Compact Heat Exchangers, A Festschrift on the 60th Birthday of Ramesh K. Shah, Aug. 2002, Grenoble, France, vol. 2, pp. 401-406.
  • Iwamoto, K., Kasagi, N., and Suzuki, Y.,
    "Nonlinear Interaction of Coherent Structures in Wall Turbulence at Low-to-moderate Reynolds Numbers,"
    IUTAM Symp. on Reynolds Number Scaling in Turbulent Flow, Princeton, Sep. 2002.
  • Iwamoto, K., Kasagi, N., and Suzuki, Y.,
    "Reynolds Number Effect on Feedback Control of Wall Turbulence,"
    Int. Symp. Dynamics and Statistics of Coherent Structures in Turbulence: Roles of Elementary Vortices, Oct. 2002, Tokyo, pp. 65-74.
  • Yoshino, T., Suzuki, Y., and Kasagi, N.,
    "Development of Genetic Algorithm Based Feedback Control System of Wall Turbulence ,"
    5th JSME-KSME Fluids Engineering Conf., CDROM, OS4-1, Nov. 2002, Nagoya.
  • Suzuki, Y., Kasagi, N. and Yoshino, T.,
    "R&D Study on Micro Sensors and Actuators for Active Control of Wall Turbulence,"
    2nd Symp. Smart Control of Turbulence, Mar. 2001, Tokyo, pp. 19-26.
  • Kurimoto, N., Suzuki, Y. and Kasagi, N.,
    "Mixing Enhancement of Coaxial Jet with Arrayed Flap Actuators for Active Control of Combustion Field, "
    2nd Symp. Smart Control of Turbulence, Mar. 2001, Tokyo, pp. 101-106.
  • Iwamoto, K., Suzuki, Y., and Kasagi, N.,
    "Effect of Nonlinear Interaction on Feedback Control of Wall Turbulence,"
    2nd Int. Symp. on Turbulence and Shear Flow Phenomena, June, 2001, Stockholm, Vol. 3, pp. 17-22.
  • Yoshino, T., Suzuki, Y., Kasagi, N., and Kamiunten, S.,
    "Assessment of the Wall Shear Stress Measurement with Arrayed Micro Hot-film Sensors in a Turbulent Channel Flow,"
    2nd Int. Symp. on Turbulence and Shear Flow Phenomena, June, 2001, Stockholm, Vol. 2, pp. 153-158.
  • Kurimoto, N., Suzuki, Y., and Kasagi, N.,
    "Active Control of Coaxial Jet Mixing and Combustion with Arrayed Micro Actuators, "
    5th World Conf. Exp. Heat Trans., Fluid Mech., and Thermodyn., Sep, 2001, Thessaloniki, pp. 511-516.
  • Suzuki, Y., Morimoto, K., Iwamoto, K., and Kasagi, N.,
    "Feedback control of wall turbulence based on the streamwise wall shear stress, "
    Bull. Am. Phys. Soc., Vol. 46, No. 10, Nov, 2001, p. 185.
  • Paitoonsrikarn, S., Kasagi, N., and Suzuki, Y.,
    "Optimal Design of Micro Bare-Tube Heat Exchanger,"
    Symp. Energy Engineering, in the 21st Century, Jan. 2000, Hong Kong, Vol. 3, pp. 972-979.
  • Yokoo, M., Kasagi, N., and Suzuki, Y.,
    "Optimal Control of Heat Transfer and Skin Friction in Wall Turbulence,"
    3rd Int. Symp. on Turbulence, Heat and Mass Transfer, Nagoya, 2000, pp. 949-956.
  • Suzuki, Y., Kasagi, N., Horiuchi, Y., and Nagoya, D.,
    "Synthesize Mixing Process in an Actively-Controlled Confined Coaxial Jet, "
    4th JSME-KSME Thermal Eng. Conf., Kobe, 2000, Vol. 3, pp. 469-474.
  • Endo, T., Kasagi, N., and Suzuki, Y.,
    "Control of Wall Shear Turbulence with Arrayed Micro Sensor/Actuator Units,"
    4th JSME-KSME Thermal Eng. Conf., Kobe, 2000, Vol. 3, pp. 493-498.
  • Suzuki, Y., Ikenoya, M., and Kasagi, N.,
    "Three-dimensional PTV Measurement of the Phase Relationship Between Coherent Structures and Dispersed Particles in a Turbulent Channel Flow,"
    3rd Int. Workshop on Particle Image Velocimetry, Santa Barbara, 1999, pp. 107-112.
  • Suzuki, H., Kasagi, N., and Suzuki, Y.,
    "Active control of an Axisymmetric Jet with an Intelligent Nozzle,"
    1st Int. Symp. Turbulence & Shear Flow Phenomena, Santa Barbara, 1999, pp. 665-670.
  • Endo, T., Kasagi, N., and Suzuki, Y.,
    "Feedback Control of Wall Turbulence with Wall Deformation,"
    1st Int. Symp. Turbulence & Shear Flow Phenomena, Santa Barbara, 1999, pp. 405-410.
  • Suzuki, H., Kasagi, N., Suzuki, Y., and Shima, H.,
    "Manipulation of a Round Jet with Electromagnetic Flap Actuators,"
    12th IEEE Int. Conf. Micro Electro Mechanical Systems (MEMS'99), Orlando, 1999, pp. 534-540.
  • Suzuki, Y., and Kasagi, N.,
    "Active Control of Wall Turbulence with an Array of Flush Mounted Flaps,"
    Bull. Ame. Phys. Soc., Vol. 42, No. 11, 1997, p. 2247.
  • Sato, K., Kasagi, N., and Suzuki, Y.,
    "Combined Velocity and Scalar Field Measurement with the Simultaneous Use of PIV and Scanning LIF,"
    10th Int. Symp. Transport Phenomena in Thermal Science and Process Engineering, Kyoto, Dec. 1997, Vol. 2, pp. 541-546.
  • Suzuki, Y., and Kasagi, N.,
    "Active Flow Control with Neural Network and Its Application to Vortex Shedding,"
    11th Symp. Turbulent Shear Flows, Grenoble, Sep. 1997, Vol. 1, pp. 9.18-9.23.
  • Satake, S., and Kasagi, N.,
    "Turbulence Control with a Wall-Adjacent Thin Layer of Spanwise Damping Force,"
    10th Symp. Turbulent Shear Flows, Penn State, Aug. 1995, Vol. 2, pp.11.1-11.6.
  • Suzuki, Y., and Kasagi, N.,
    "Drag Reduction Mechanism on Micro-Grooved Riblet Surface,"
    Near-Wall Turbulent Flows,Proc. Int. Conf. Near-Wall Turbulent Flows, R. M. C. So, C. G.Speziale and B. E. Launder, eds., Elsevier, Amsterdam, 1993, pp.709-718.
  • Suzuki, Y., and Kasagi, N.,
    "On the Turbulent Drag Reduction Mechanism Above a Riblet Surface,"
    24th AIAA Fluid Dynamics Meeting, Orlando, July 1993, Paper No. 93-3257.
  • Suzuki, Y., and Kasagi, N.,
    "Evaluation of Turbulence Measurements with Hot-Wires Using a Direct Numerical Simulation Data Base,"
    Int. Symp. Engineering Turbulence Modelling and Measurements, Dubrovnik, Sep. 1990, pp. 361-370.

Publications